Curing Techniques for Improving the Compressive Strength of Concrete

concrete curing
concrete curing

What Is Concrete Curing?

Concrete curing is the process of maintaining adequate moisture in concrete within a proper temperature range in order to aid cement hydration at early ages. Hydration is the chemical reaction between cement and water that results in the formation of various chemicals contributing to setting and hardening. The hydration process is affected by the initial concrete temperature, the ambient air temperature, the dimensions of the concrete, and mix design. Therefore, for this process to progress well, in-situ concrete must have sufficient moisture and a temperature that favours this chemical reaction at a rapid and continuous rate.

Get Your First SmartRock Concrete Sensor for FREE

Giatec SR demo kit_
Giatec SR demo kit_

The American Concrete Institute (ACI) recommends a minimum curing period corresponding to attaining 70% of the compressive strength of concrete. It is often specified that this can be achieved after seven days of curing. However, 70% strength can be reached quicker when concrete cures at higher temperatures, or when certain admixtures are used in the concrete mix. Similarly, more time may be needed for curing when concrete or ambient temperatures are lower. Typically, 20 degrees Celsius (68°F) is considered an ideal curing temperature.

Why Concrete Curing Is Important

Careful control of moisture and temperature of your in-situ concrete during curing is an essential part of quality control and quality assurance of your concrete structure. Proper curing techniques will prevent in-situ concrete from drying, shrinking, and/or cracking, and ultimately affecting the performance of your structure, particularly at the cover zone. Curing of concrete should occur as soon as it has been placed. It is also essential that continuous monitoring of concrete curing conditions be carried out for seven days. If water evaporates from the concrete before it has attained its maximum strength, there will not be enough water remaining in the concrete to fully hydrate the cement and achieve maximum compressive strength. This is especially true during extreme weather conditions, when your concrete slab is subjected to various environmental elements and strength development of your concrete can be compromised.

3 Techniques for Efficient Concrete Curing

Many factors affect the rate at which water evaporates from freshly placed concrete. This includes air temperature, humidity, concrete temperature, and wind speed. As a result, many techniques have been developed to help concrete retain moisture at the early ages. These methods are used to:

  1. Maintain the presence of water in the concrete during the early hardening period,
  2. Reduce the loss of water from the surface of the concrete, and
  3. Accelerate concrete strength gain by supplying heat and additional moisture.

The method (or combination of methods) chosen depends on factors such as availability of curing materials, size, shape, and age of concrete, production facilities (in place or in a plant), aesthetic appearance, and economics. As a result, curing often involves a series of procedures used at a particular time as the concrete ages. The timing of each procedure depends on the degree of hardening of the concrete needed to prevent the procedure from damaging the concrete surface.

Curing Techniques for Improving the Compressive Strength of Concrete

1) Maintaining Moisture

Ponding and Immersion

Ponding is typically used to cure flat surfaces, such as pavements and floors, as earth and sand around the perimeter of the concrete surface can retain a pond of water. Ponding is an ideal method for preventing loss of moisture from the concrete; it is also effective for maintaining a uniform temperature throughout the concrete. Immersion of a finished concrete element is commonly used for curing test specimen.

Read more about the importance of cylinder curing conditions in this article

Spraying and fogging

Spraying and fogging are used when the ambient temperatures are well above freezing, and the humidity is low. Fog mist is applied through nozzles or sprayers to raise the relative humidity of the air over flatwork, thus slowing evaporation from the surface. Fogging is used to minimize plastic shrinkage cracking. If sprinkling is done at intervals, the concrete must be prevented from drying between applications of water by using burlap or similar materials; otherwise, alternate cycles of wetting and drying can cause surface cracking.

Saturated wet coverings

Wet coverings saturated with water, such as burlap, cotton mats, rugs, or other moisture-retaining fabrics, are commonly used for curing. The materials should be placed as soon as the concrete has hardened enough to prevent surface damage. They should be kept constantly wet so that a film of water remains on the concrete surface throughout the curing period.

Left-in-place forms

Left in place forms usually provide satisfactory protection against moisture loss for formed concrete surfaces. The forms are usually left in place as long as the construction schedule allows. If the forms are made of wood, they should be kept moist, especially during hot, dry weather.

2) Reducing Loss of Water

Covering concrete with impervious paper or plastic sheets

Impervious paper and plastic sheets can be applied on thoroughly wet concrete, such as polyethylene film. This material is a lightweight, effective moisture retarder that is easy to apply. During placement, the concrete surface should be hard enough to prevent surface damage.

Applying membrane-forming curing compounds

Membrane-forming curing compounds are used to retard or reduce evaporation of moisture from concrete. They can be clear or translucent and white pigmented. White-pigmented compounds are recommended for hot and sunny weather conditions to reflect solar radiation. Curing compounds should be applied immediately after final finishing and must comply with ASTM C3094 or ASTM C13155.

3) Accelerating Concrete Strength Gain

Live steam

Live steam and high-pressure steam are the two methods of steam curing. The temperature for live steam should be kept at about 140 degrees Fahrenheit or less until the desired concrete strength is achieved.

Heating coils

Heating coils are usually used as embedded elements near the surface of concrete elements. Their purpose is to protect concrete from freezing during cold-weather concreting.

Electrical heated forms or pads

Electrical heated forms or pads are primarily used by precast concrete producers.

Concrete blankets

Concrete insulation blankets are used to cover and insulate concrete surfaces subjected to freezing temperatures during the curing period. When using concrete blankets, make sure that the concrete is hard enough to prevent surface damage.

Everything you need to know about cold weather concreting here

SmartRock sensor installed on rebar

Curing for Compressive Strength of Concrete

Freshly mixed concrete normally contains more water than is required for hydration of the cement; however, excessive loss of water by evaporation can delay or prevent adequate hydration, especially in the surface of the slab. These techniques for retaining moisture of in-situ concrete are therefore important for proper hydration so that concrete can gain sufficient compressive strength.

Curing directly influences the quality of your overall structure. Strength gain is rapid at early ages but continues more slowly for an indefinite period. Proper curing will increase durability, strength, water-tightness, abrasion resistance, volume stability, and resistance to freezing and thawing.

The process of placing and curing concrete on-site requires precise temperatures so that the structural integrity of the concrete is not damaged. With SmartRock®, a wireless concrete temperature and strength measurement sensor, you no longer have to worry about ambiguous wait times. SmartRock delivers real-time, accurate data to your mobile device every 15 minutes with the free SmartRock app.

This completely wireless sensor allows team members to work efficiently without worrying about protruding wires, or having to search for wires under heating blankets, when relying on external data loggers. The sensor is fully embedded in the concrete and secured on the rebar within the formwork. SmartRock continuously monitors the effect of ambient temperatures and the external environment on your in-situ concrete, making it easier to control concrete curing and ensure optimal conditions for compressive strength gain. In addition, real-time results allow contractors to optimize the heating process, decrease energy costs, and save time in their project schedule by knowing when concrete has gained sufficient strength for subsequent construction operations, such as formwork removal or post-tensioning.

Read how S&F Concrete Contractors’ used SmartRock to monitor concrete curing

Sources
CCANZ
PCA
NRMCA

Editors Note: This post was originally published in January 2019 and has been updated for accuracy and comprehensiveness.

8 Responses

  1. It is a pity that you forgot about curing of high-strength / high-performance concrete, for which conventional methods of curing based on maintaining moisture, either by supplying water from outside or by sealing the surface to prevent evaporation, do not work. This type of concrete is prone to cracking at an early age due to self-desiccation and autogenous shrinkage. The solution is to apply so-called internal curing. You are welcome to refer the article “Novel techniques for concrete curing” published in Concrete International, 2005, 27(9):39-42.

    1. Hello, thank you for your interest and for sharing this information regarding UHPC. The purpose of this article was to cover conventional techniques for curing concrete, however, this is a great proposition for a new post, thanks!

  2. It was interesting when you talked about how concrete needs to retain some moisture in order to reach its optimal level of compressive strength. My husband and I are looking for a ready-mix concrete supplier so we can install a driveway for the rural home we purchased at the end of last month. Learning about curing time helped me feel a lot more prepared to ask the right questions once we find a concrete supplier!

    1. “Thank you for your question

      The recommended curing time on any concrete element will depend on internal and external factors such as mix proportions, size and shape of the slab, ambient conditions, specified strength, etc. For instance, is this slab submitted to direct sunlight, dry environment and wind incidence? In this case, the chosen curing procedure is extremely important.

      ACI 301 recommends a minimum curing period comparable to concrete attaining 70% of the specified compressive strength. Typically this target is obtained within 7 days, but it varies from mix to mix. The primary focus when curing a slab is to prevent shrinkage cracks related to loss of water due to evaporation. Therefore, it is always recommended to carefully evaluate the environment where your slab/concrete element is located.

      Furthermore, in some cases such as concrete pavements or industrial floors, it is hard/nearly impossible to maintain a layer of water on the concrete to provide curing conditions. In such cases, tarps or chemical curing can be used. By mindfully selecting the most appropriate curing procedure, one can prevent cracks and ensure more durability in the long run.

      For more information about curing procedures, refer to the following link: https://www.cement.org/learn/concrete-technology/concrete-construction/curing-in-construction

  3. Excellent article, very successful, where it is clearly explained not only the techniques but also the importance of curing

Leave a Reply

Your email address will not be published.

Related Articles

cement vs concrete

Back to Basics: Cement vs Concrete

How many times have you heard people use the words cement and concrete interchangeably? Probably enough for you to wonder if there is a difference at all. While there are some ways in which the terms are related, the answer is simple: concrete and cement are fundamentally different. In this blog we will discuss all you need to know to answer the question: cement vs concrete, are they different?

concrete testing lab

Revolutionizing Third-Party Concrete Testing with SmartRock® Wireless Sensors

Often, third-party testing agencies face several challenges with standard temperature and strength monitoring systems. Some of these involve relying on multiple wired components and expensive concrete monitoring systems. Subsequently, concrete testing lab facilities require extra time to produce accurate data, and this presents a burden when contractors need this information right away.  Get Your First SmartRock Concrete Sensor for FREE Free Demo Kit How Can Technicians Solve This Challenge? SmartRock is the world’s leading wireless sensor for monitoring concrete curing and hardening. This fully embedded sensor…

Book your meeting with us at World of Concrete,
January 17-19, 2023

The Big 5

Book your meeting with us at The Big 5, December 5-8

We use cookies to provide you with a better experience, analyze site traffic and assist in our marketing efforts. By continuing to use this website, you consent to the use of cookies in accordance with our Privacy Policy Page.